A complete replacement
Replace the regulator and motor together without transferring the old motor. A single assembly simplifies part selection and installation planning.
SERIES WRM · COMPLETE ASSEMBLIES
Regulator withMotor Assemblies
One part number. One complete solution.
A window regulator and matched motor, supplied as one assembly. From conventional DC systems to intelligent LIN BUS applications, Han Yale brings mechanical fit and motor control together for an application-specific replacement.
12V / 24V2-Pin DCHall / RippleLIN BUS 2.x
HAN YALE / SERIES WRMREGULATOR + MOTOR
Supply FormatComplete Assembly
FitmentOE-Matched
ConfigurationDC / Smart Motor
Mechanical precision meets motor control
Engineered to work together.
The right replacement is more than a matching mounting pattern. Motor direction, regulator travel, connector layout and control signals all matter.
Matched to the application
Mounting points, glass attachment, travel and connector orientation are checked against the intended vehicle and door position.
Control compatibility
For smart applications, Hall signals, ripple profiles or LIN communication must match the vehicle’s door electronics—not just move the glass.
Select by the original system
Three control configurations.
Choose the assembly that matches the vehicle’s original architecture. These configurations are application-specific and are not interchangeable.
Conventional drive
Standard DC Assemblies
Complete regulator assemblies for traditional power-window systems.
- Standard 2-pin DC motor
- 12V or 24V applications
- Matched connector pinout and rotation polarity
- Passenger-car and commercial-vehicle applications
Position feedback
Hall / Ripple Assemblies
Assemblies matched to vehicles that use motor feedback for window position and control.
- Dual Hall or ripple-count configurations
- Application-specific pulse or ripple characteristics
- Matched regulator travel and motor behaviour
- One-touch and anti-pinch support where specified
Integrated intelligence
LIN BUS Assemblies
Smart motor and regulator combinations for network-controlled door systems.
- LIN BUS 2.x configurations
- Motor controller integrated into the assembly
- Application-matched communication and diagnostics
- Vehicle-specific control and initialization requirements
Voltage, feedback, one-touch operation and anti-pinch functions depend on the selected part number and vehicle system. Confirm specifications before ordering.
Series WRM / Technical overview
Specify the complete system.
| Specification | Available configuration / confirmation required |
|---|---|
| Product format | Window regulator with matched motor, supplied as a complete assembly. |
| Operating voltage | 12V or 24V, according to vehicle application. |
| Motor control | Standard 2-pin DC, Hall feedback, ripple-count or LIN BUS 2.x. |
| Door position | Confirm front / rear and left / right, along with left-hand or right-hand drive where relevant. |
| Mechanical interface | OE-specific mounting points, glass attachment, travel and regulator geometry. |
| Electrical interface | Vehicle-specific connector, pin count, polarity and signal requirements. |
| Smart functions | One-touch, anti-pinch and diagnostic feedback on applicable configurations. |
| Installation | Follow vehicle service instructions; initialization or relearn may be required. |
| Validation documents | Request the test scope and applicable compliance documentation for the selected part number. |
Tested on real vehicles
Fit is mechanical.
Compatibility goes further.
Han Yale combines regulator manufacturing with electronics and software development. Our verification approach considers the assembly, the door module and the vehicle as a connected system.
Taiwan EngineeringVietnam Production
Confirm the physical fit
Review mounting geometry, glass attachment, connector clearance and full regulator stroke.
Match motor behaviour
Check rotation direction and the feedback characteristics required by the original control system.
Verify vehicle interaction
For smart assemblies, check one-touch operation, anti-pinch behaviour and communication on the applicable vehicle or door module.
Document the selected configuration
Confirm the part number, electrical specification and installation requirements before supply.
Before you order
Assembly & fitment questions.
What is included in a regulator with motor assembly?
The window regulator mechanism and its matched motor are supplied together. Confirm any included brackets, fasteners or additional components against the selected part number.
Does every assembly include one-touch and anti-pinch?
No. Standard DC and smart configurations support different control systems. One-touch and anti-pinch depend on the assembly specification and the vehicle’s electronics. Match the original equipment configuration.
Can a 2-pin DC assembly replace a LIN BUS version?
These systems use different control architectures and should not be treated as interchangeable. Supply the OE number and connector details so the correct configuration can be identified.
Will the window need initialization after installation?
Some vehicles require a window initialization or relearn procedure after replacement. Follow the vehicle manufacturer’s service procedure for the specific model.
What information should I send for a fitment check?
Send the vehicle make, model, year, market, door position, OE reference number and voltage. Photos of the original assembly and connector help identify the correct configuration.
Find your application
Start with the right assembly.
Share your OE number, vehicle details and door position. Our team can help confirm the required regulator, motor and control configuration for your sourcing needs.
For sourcing inquiries, include your estimated quantity and destination market.